高压径向均压绝缘堆设计

马勋; 邓建军; 姜苹; 王勐; 刘宏伟; 袁建强; 王凌云; 李洪涛

doi:10.11884/HPLPB201426.105004

强激光与粒子束

高压径向均压绝缘堆设计

, , , , , , ,

马勋, 邓建军, 姜苹, 王勐, 刘宏伟, 袁建强, 王凌云, 李洪涛. 2014: 高压径向均压绝缘堆设计, 强激光与粒子束, null(10): 105004. doi: 10.11884/HPLPB201426.105004

引用本文:

马勋, 邓建军, 姜苹, 王勐, 刘宏伟, 袁建强, 王凌云, 李洪涛. 2014: 高压径向均压绝缘堆设计, 强激光与粒子束, null(10): 105004. doi: 10.11884/HPLPB201426.105004

MaXun, DengJianjun, JiangPing, WangMeng, LiuHongwei, YuanJianqiang, WangLingyun, LiHongtao. 2014: Design of high-voltage hold-off radial insulator stack with grading rings, High Power Lase and Particle Beams, null(10): 105004. doi: 10.11884/HPLPB201426.105004

Citation:

MaXun, DengJianjun, JiangPing, WangMeng, LiuHongwei, YuanJianqiang, WangLingyun, LiHongtao. 2014: Design of high-voltage hold-off radial insulator stack with grading rings, High Power Lase and Particle Beams, null(10): 105004. doi: 10.11884/HPLPB201426.105004

高压径向均压绝缘堆设计

中国工程物理研究院流体物理研究所，脉冲功率科学与技术重点实验室，四川绵阳 621900

Design of high-voltage hold-off radial insulator stack with grading rings

摘要: 以形成线储能结合脉冲压缩方式产生数 MV高压输出,是脉冲功率系统中常见的技术途径,其中绝缘堆是该类装置工程成败的关键。分析了几种径向均压绝缘堆的均压机制,基于静电场分析程序对径向均压绝缘堆结构进行了优化设计,给出了径向电阻的设计方法。研究表明：采用均压环且均压环与径向电阻电气接触的绝缘堆结构可以获得较均匀的径向电场分布,而径向电阻是绝缘堆设计的关键。在有效作用时间100 ns的4.5 MV加载电压下,优化设计的绝缘堆阴极三相点电场控制在25 kV/cm,Martin电场约120 kV/cm,低于理论击穿值。
- 闪光 X光机 /
- 径向均压绝缘堆 /
- 电场分布 /
- 径向电阻
Abstract: High-voltagehold-offinsulatorstackisthemostcrucialcomponentinpulsedpowersystemwhileapplyingpulse forming line and pulse compress technology to generating several MV voltage output.The voltage potential distribution mecha-nism of several radial insulator stacks was studied.An optimized insulator stack configuration was acquired based on static electric field analysis program,and designing method of radial resistor is proposed.Results showed that much uniform electric field distri-bution of insulator stack was obtained by using grading rings together with the electrical contact of grading rings and radial resis-tor,the radial resistor becomes the key to the performance of insulator stack.With an applied voltage of 4.5 MV and a duration of 100 ns,the electric field of triple point and Martin were about 25 kV/cm and 120 kV/cm respectively,lower than the theoreti-cal flashover value.

计量

文章访问数: 280
HTML全文浏览数: 116
PDF下载数: 19
施引文献: 0

高压径向均压绝缘堆设计

中国工程物理研究院流体物理研究所，脉冲功率科学与技术重点实验室，四川绵阳 621900

关键词:

摘要: 以形成线储能结合脉冲压缩方式产生数 MV高压输出,是脉冲功率系统中常见的技术途径,其中绝缘堆是该类装置工程成败的关键。分析了几种径向均压绝缘堆的均压机制,基于静电场分析程序对径向均压绝缘堆结构进行了优化设计,给出了径向电阻的设计方法。研究表明：采用均压环且均压环与径向电阻电气接触的绝缘堆结构可以获得较均匀的径向电场分布,而径向电阻是绝缘堆设计的关键。在有效作用时间100 ns的4.5 MV加载电压下,优化设计的绝缘堆阴极三相点电场控制在25 kV/cm,Martin电场约120 kV/cm,低于理论击穿值。

English Abstract

Design of high-voltage hold-off radial insulator stack with grading rings

中国工程物理研究院流体物理研究所，脉冲功率科学与技术重点实验室，四川绵阳 621900

Keywords:

Abstract: High-voltagehold-offinsulatorstackisthemostcrucialcomponentinpulsedpowersystemwhileapplyingpulse forming line and pulse compress technology to generating several MV voltage output.The voltage potential distribution mecha-nism of several radial insulator stacks was studied.An optimized insulator stack configuration was acquired based on static electric field analysis program,and designing method of radial resistor is proposed.Results showed that much uniform electric field distri-bution of insulator stack was obtained by using grading rings together with the electrical contact of grading rings and radial resis-tor,the radial resistor becomes the key to the performance of insulator stack.With an applied voltage of 4.5 MV and a duration of 100 ns,the electric field of triple point and Martin were about 25 kV/cm and 120 kV/cm respectively,lower than the theoreti-cal flashover value.

全文HTML

参考文献 (0)

下载: 全尺寸图片幻灯片

返回文章

用微信扫码二维码

分享至好友和朋友圈

高压径向均压绝缘堆设计

Design of high-voltage hold-off radial insulator stack with grading rings

计量

出版历程

高压径向均压绝缘堆设计

English Abstract

Design of high-voltage hold-off radial insulator stack with grading rings

全文HTML

目录