-
Biomass, as the only renewable carbonaceous resource, is widely available and environmentally resourceful in the nature, and thus has the immense potential to address the challenges of the excessive consumption of fossil fuels along with serious environmental pollution and global warming [1]. Biochar, bio-oil and gas have been produced from the thermal decomposition of biomass over the past decades, which show great potential in the applications for the preparation of fuels and chemicals, and energy storage, etc. [2, 3].
Previous studies reported that a very small amount of alkali metals (e.g. sodium and potassium) as the inherent inorganic elements in biomass, as represented by cellulose and lignin, showed profound catalytic effects on the product distribution from biomass pyrolysis [2−6]. To date, the majority of studies toward pyrolysis of cellulose and lignin have focused on the generation of volatile products gas and bio-oil in which the product distribution can be tuned by the ratio between alkali metals and biomass. The addition of alkali metal salts improved the thermal reactivity of cellulose and lignin, altering the distribution of volatile products during the pyrolysis reaction process [6−8]. In the process of cellulose pyrolysis, the alkali metal salts promoted the cleavage of the glycosidic bonds, dehydration and ring-opening reactions [4, 7, 9], whereas they facilitated the cleavage of the C–C and ether bonds during the initial pyrolysis process of lignin, and secondary reactions such as decarbonylation, demethoxylation, dehydration, and side-chain elimination [2, 10, 11]. The influence of alkali metal/biomass ratio on the formation of char has been rarely studied [1, 12].
In this work, Na2CO3 was used to investigate the catalytic effects on the structure and property of char from cellulose and lignin pyrolysis. The ratios of Na2CO3 to cellulose or lignin ranged from 1 wt% to 100 wt%. These acquired chars were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Raman spectroscopy. The formation of a tubular structure and a significant change of crystal orientation of char were observed from these tests. Some char products were then employed as anode materials in sodium-ion batteries to promote their commercial application on energy storage. Cellulose char exhibited a higher sodium storage capacity than that of lignin char. This work deepens the understanding of catalytic pyrolysis of biomass and offers a promising approach for electrochemical application of biomass.
-
Materials, α-cellulose and lignin (Dealkaline) were purchased from Shanghai Macklin Biochemical Co., Ltd. The alkali metal salt Na2CO3 (99.5%) was supplied by J&K Scientific Ltd. The salt was ground into powder and then mixed with cellulose or lignin. The mass ratios of Na2CO3 to cellulose or lignin were 1 wt%, 2 wt%, 4 wt%, 6 wt%, 10 wt%, 20 wt%, 50 wt%, and 100 wt%, where the mechanical mixing compounds were named as cel1−cel8 and lig1−lig8. The hydrochloric acid and ester-based electrolyte were supported from Guangzhou Chemical Reagent Factory and DoDoChem Reagent Network, respectively. The conductive carbon black and sodium alginate were gotten from DX Time Co., Ltd.
-
The char was prepared in an alundum tube furnace made by Hefei Kejing Material Technology Co., Ltd. under an argon atmosphere with a flow rate of 100 sccm. The decomposition experiments were carried out from 50 °C to 100 °C at a linear heating rate of 5 °C/min and kept isotherm for 1 h. Then the furnace temperature increased up to 600 °C with 10 °C/min. After that, it was cooled down naturally to ambient temperature and black solids were obtained. In the next step, the solid products were ground into powders and transferred into a beaker. Subsequently, the black powders were leached with 1 mol/L HCl for 24 h and fully washed with ultrapure water until the filtered water reached a neutral pH. At last, the solid residues left by filtration were dried at 70 °C in an oven overnight to get the char. The prepared chars without the catalysis of Na2CO3 were labelled as C-cel and C-lig, where cel and lig stood for cellulose and lignin respectively. The chars acquired from catalytic pyrolysis of cellulose and lignin by disparate proportions of Na2CO3 were marked as C-cel1 to C-cel8 and C-lig1 to C-lig8.
-
The 2025-type coin cells were assembled in an argon filled glovebox. The electrode slurry was made by blending active material (80 wt%), conductive carbon black (10 wt%), and sodium alginate (10 wt%) in mixed ethanol/water solvent. Then it was coated on a Cu foil to fabricate working electrodes. A typical mass loading of active material on each anode current collector was about 1.2 mg/cm2. The ester-based electrolyte was a solution of 1.0 mol/L of NaPF6 in ethylene carbonate/diethyl carbonate (1:1 by volume).
-
Morphological characterization of char was conducted via scanning electron microscopy (Verios 5 XHR, Thermo Scientific, Czech Republic). The diffraction measurement was performed with 2θ scan range from 5° to 60° using a high-flux X-ray diffraction (D8 ADVANCE, Bruker, Germany) equipped with Cu Kα radiation. The Raman spectra were obtained by a Raman spectrometer (inVia Qontor, Renishaw, Britain) using 532-nm laser. The coin-type half cells were measured in Land CT2001A battery tester with a voltage range of 0.005−3.0 V.
-
As exhibited in FIG. 1, the raw materials of both cellulose and lignin and their derived char without further grinding are found to be in the state of powder, implying that melt and polymerization are difficult to occur among raw particles. FIG. 1 (a) and (c) show that there are obvious morphological differences between cellulose and lignin. The cellulose consists of characteristic linear bundles, which are closely crisscrossed one another. In addition, the surface of each bundle exhibits dense wrinkle-like morphology. In contrast, the surface of lignin is overlaid with laminated microstructures.
Although a large amount of volatile organic matters, including gas and bio-oil, are released during thermal decomposition [1], the initial morphological structures of cellulose and lignin are almost retained in char though containing some defective holes, as disclosed in FIG. 1 (b) and (d). However, as compared to the structures of initial biomass, the compactness of linear bundles becomes lower due to the loss of vapors in the cellulose pyrolysis. In addition, a lot of tiny vesicles are clearly visible on the surface of lignin char in FIG. 1(d) because of the emission of volatiles and simultaneous aromatization reactions in the decomposition process of lignin [13].
The SEM images of char produced from the catalytic pyrolysis of cellulose and lignin are shown in FIG. 2. Na2CO3 catalysts were removed from these samples for better characterizations. As can be seen in FIG. 2(a)−(h), although the linear bundles and wrinkles on cellulose char still survived upon catalysis of Na2CO3, the combination of bundles is weakened, which is associated with the generation of massive pores and cavities. Noticeably, a number of tubular structures are observed on the char surface obtained from the pyrolysis of 10 wt%Na2CO3/cellulose (FIG. 2(e)), which are dense, entangled, and randomly oriented.
We note that the syntheses of tubular structure by conventional methods, including arc-discharge, chemical vapor deposition, laser ablation, template methods, flame synthesis, and electrolysis, typically involve complex pathways [14]. In contrast, pyrolysis of biomass offers an alternative facile method for the fabrication of tubular structure. Conventional pyrolysis approach generally requires the participation of expensive transition metals as the catalysts [14], weakening their commercial prospect. Therefore, the synthesis of tubular structure from a cheap approach by Na2CO3/cellulose pyrolysis as reported here exhibits its great advantages.
We propose a possible mechanism for the generation of tubular structure. Joy and workmates believed that the volatiles passed through the porous structures of biomass, followed by condensation and re-solidification to yield tubular structure [14−16]. In this process, tiny vesicle was firstly generated which acted as active nucleation sites to initiate the formation of tubular structure. They postulated such transformation catalyzed by the inherent inorganic species in biomass, such as Ca, K, and Fe. We speculate that cellulose pyrolysis has experienced a similar pathway to form tubular structure by the catalysis of Na2CO3. This is partially supported by the appearance of vesicles at the sample prepared at a higher Na2CO3 concentration, e.g. the sample shown in FIG. 2(f). It is therefore plausible to expect that the transformation from vesicles to tubular structures could be enhanced at a proper Na2CO3 concentration.
FIG. 2(i)−(p) are the SEM images of char derived from the catalysis of Na2CO3 on lignin pyrolysis. In contrast to lignin char without catalysis of Na2CO3, the formation of vesicles is suppressed by Na2CO3, leading to a dramatic decrease in the quantity of vesicles.
As seen in the SEM images of all the chars, tubular structures are only found on the surface of cellulose char when the mass ratio of Na2CO3 to cellulose is 10 wt%, while it was absent in lignin char. Cellulose as a macromolecular saccharide is comprised of glucose unit connected by β-1,4-glycosidic bonds [15]. Lignin as a phenolic polymer mainly consists of three complex polymeric compounds, which attach different numbers of methoxyl groups on an aromatic ring [15]. Therefore, monosaccharides might play a role of effective carbon sources in the synthesis of tubular structures.
-
X-ray diffraction (XRD) spectra were acquired to further investigate the crystalline structures of prepared char. The X-ray diffraction profiles for cellulose, C-cel, lignin and C-lig are shown in FIG. 3. As seen in the XRD profile of cellulose sample, two peaks at Bragg angle (2θ) of 15.2° and 16.3° are assigned to the plane (101) and (
$10\bar 1$ ) of cellulose I, respectively [17]. The most intense peak of cellulose appears at 2θ angle of 22.6°, which is assigned to cellulose I crystallographic plane (002) accompanying with a small part of cellulose Ⅱ crystallographic plane (101) [17]. The shoulder peak at angle 2θ = 20.5° is attributed to the diffraction from ($10\bar 1 $ ) plane of cellulose II [17]. The angle 2θ = 34.6° is from (040) reflection of cellulose I [17]. There is an additional crystal lattice at 43.3° in the XRD curve of cellulose, and the peak is consistent with the high crystallinity of cellulose under investigation of the isolation and characterization of cellulose and α-cellulose from date palm biomass waste [18]. As for the XRD curve of C-cel, there are two broad and weak peaks at around 23.1° and 43.2°. The two diffraction peaks are ascribed to the crystalline planes (002) and (100/101) of graphited carbon structure, respectively [19]. It can be interpreted that a stack of aromatic layers with amorphous structures were formed during cellulose pyrolysis.In the XRD profiles of lignin and its char, two peaks near the diffraction angles (2θ) of 23° and 43° are detected. They are ascribed to the (002) and (100/101) plane of graphite respectively [19]. As for lignin, a weak and wide peak at 22.5° indicates that lignin is a typical non-crystalline polymer. It is a known fact that lignin is a three-dimensional amorphous and highly aromatic polymer mainly composed of cross-linked phenyl-propane units [20, 21]. After the thermal degradation of lignin, the (002) peak shifts from 22.5° to 23.5°, becoming closer to that of graphite (26.6°) [22]. Additionally, the (002) peak of C-lig becomes sharper than lignin. These results illustrate that lignin char has a much higher degree of long-range order of (002) crystalline structure. A small and sharp peak at 2θ = 43.2° in the XRD curve of lignin indicates that there is a high crystallinity of (100/101) plane [23]. However, there is only a weak and wide (100/101) peak exposed in the XRD curve of lignin char. Above results prove that the (100/101) crystal plane is damaged in the process of lignin pyrolysis, while a (002) crystal plane is developed.
The X-ray diffraction profiles of char from the catalytic pyrolysis of cellulose and lignin are exhibited in FIG. 4 (a) and (b), respectively. There are two peaks near 2θ = 23.1° and 51.1° for all the profiles in FIG. 4. The two peaks could be attributed to the typical crystalline plane (002) and (004) of graphited carbon [24, 25]. It is revealed that the crystalline structures of char from both cellulose and lignin pyrolysis under the catalysis of Na2CO3 are almost the same.
Comparing the XRD curves of the prepared char before and after catalytic reactions, the (002) peak is almost retained after catalysis, while the (100/101) peak disappears and (004) peak is evolved. Na2CO3 plays the role in contributing to the growth of (004) plane, but suppressing the formation of (100/101) plane. Nonetheless, the concentration of Na2CO3 has a negligible influence on the crystal structure of char.
-
Raman spectroscopy technique has been applied for detecting the structural deformations of carbon materials. Specific bands relating to the graphite structures are detected in the Raman spectra for all char containing D and G bands in FIG. 5. The D band at a frequency around 1336 cm−1 is originated from the dangling bonds in disordered carbon, whereas G band near a frequency of 1588 cm−1 is identified as the graphitic component of synthetic char associated with the in-plane vibration of the sp2 carbon atoms [26]. The position and width of both D and G band peaks do not have evident changes for all char. The ratio of the D band to G band intensity (ID/IG) is a remarkable indicator for assessing the nature of carbon phase in terms of carbon order and graphite structure [15, 26]. An increase in intensity ratio indicates that the extent of long-range ordered crystalline of char decreased. The consequences of ID/IG range from 0.8 to 1.1 in FIG. 5, whereas there are no regular trends between ID/IG ratio and Na2CO3 concentration, implying that the quality of crystalline of cellulose and lignin char does not have obvious relationship with Na2CO3.
-
The assembled half-cells were tested in a voltage range of 0.005–3 V. FIG. 6 presents the electrochemical performance of C-cel, C-cel5, C-cel8, and C-lig. For the cyclic performance of the four carbon materials, the first 3 cycles were completed at 50 mA·g–1 to activate the char, and the remaining cycles were carried out at 200 mA·g–1. The discharge capacity of cellulose char and lignin char in the first cycle are about 274 and 36 mA·h·g–1, respectively. Subsequently, the discharge capacity goes down to a relatively stable values near 61 (C-cel) and 12 mA·h·g–1 (C-lig). The sodium storage capacity of cellulose char is much higher than that of lignin char. Based on the excellent storage capacity of cellulose char, a further comparison is made between cellulose char before and after catalysis. The discharge capacity of C-cel5 and C-cel8 in the first cycle is about 207 and 274 mA·h·g–1, they finally stabilizes at 39 and 65 mA·h·g–1. The sodium storage capacity of C-cel8 and C-cel is comparable, but higher than C-cel5. The crystal structure and graphitization degree of C-cel, C-cel5, and C-cel8 are similar, but they show different morphological structures. Therefore, we speculate that the pores of tubular structure in C-cel5 increase the transport pathways of sodium ions and suppress the sodium ion transport rate to a certain degree, resulting in a poorer sodium storage capacity [27].
The Coulombic efficiency of the four materials exhibits a similar trend. The Coulombic efficiency in the first cycle is around 30%, then it goes up to about 100% after the first 5 cycles. As seen in the discharge curves for the first 3 cycles, there is a distinct difference between the first discharge curve and other two curves for all the carbon materials. As reported, the high discharge capacity in the first cycle is due to the initial irreversible sodium consumption and the inevitable formation of a solid electrolyte interphase (SEI) film [28−30].
Rate performance of the four materials was executed at a current density ranging from 0.05 A/g to 5 A/g. The specific capacity is declined with the increase of current density for all carbon materials. Afterwards, the specific capacity returns when the current density is back to 0.2 A/g. The four carbon samples have a similar trend in the aspect of rate performance. Comparing the rate performance of four materials, C-cel and C-cel8 have the best rate performance, higher than C-cel5, while C-lig has the lowest rate performance.
-
The char has been synthesized via thermal decomposition with the catalytic effects of Na2CO3, the ratios of Na2CO3 to cellulose or lignin range from 1 wt% to 100 wt%. In this work, the Na+ makes a profound impact on cellulose and lignin charring. Na2CO3 promotes the fragmentation of combined bundles of cellulose. More importantly, Na2CO3 plays a crucial part in the formation of plentiful tubular structure on the surface of cellulose char. As for the surface of lignin char, Na2CO3 inhibits the formation of small vesicles. The results of Raman spectroscopy and XRD illuminate that the chars derived from cellulose and lignin including the catalysis of Na+ are typically non-crystalline graphite. However, the alkali metal ions alter the crystal structures through promoting the growth of (004) plane and suppressing the formation of (100/101) plane. The Coulombic efficiency is about 100% after the first 5 cycles for the tested char. From the whole electrochemical performance, the discharge capacity of C-lig is much lower than the char from cellulose pyrolysis or its catalytic pyrolysis. Notably, the existence of tubular structure is harmful for the transformation of Na+ to shorten the sodium storage capacity. The systematic investigation of the cellulose and lignin char under the catalytic effects of Na2CO3 is of great significance for pyrolysis mechanism and electrochemical application of biomass.
Effect of Na+ on Preparation of Biochars and Their Applications in Energy Storage
- Received Date: 01/04/2024
- Available Online: 27/08/2025
-
Key words:
- Cellulose char /
- Lignin char /
- Catalytic pyrolysis /
- Sodium storage capacity
Abstract: This work investigated the effect of Na2CO3 on the char structures of cellulose and lignin, respectively, and examined the electrochemical performance of the char by acting as an active material for coin cells. The morphology of char can be significantly steered by the concentration of Na2CO3. Scanning electron microscopy analysis demonstrated that the introduction of Na2CO3 into cellulose at an appropriate concentration led to the formation of tubular structure on its surface after pyrolysis, whereas the tubular structure was absent in the lignin char with the addition of Na2CO3 at any concentrations. X-ray diffraction and Raman spectroscopy characterizations revealed that all the obtained chars from both cellulose and lignin, with or without Na2CO3, were ascribed to non-crystalline graphite. Nevertheless, the crystal orientation of graphite from cellulose and lignin changed after the catalysis of Na2CO3. Further electrochemical tests showed that cellulose char had a higher sodium storage capacity than that of lignin char. The excellent electrochemical performance of carbon materials derived from cellulose might hold a prospective application in the field of energy storage.
首页
登录
注册


DownLoad: