-
Two-dimensional (2D) materials, characterized by atomic-scale thickness, are versatile in functional applications. When these materials are stacked at the atomic scale, they often exhibit enhanced composite properties and functional diversity [1−8]. However, the stacking process typically involves mechanical exfoliation and transfer, which is complex and step-intensive. This method also invariably introduces interlayer impurities or contaminants that can obscure the intrinsic properties and functionalities of the composite systems, thus hindering consistent and reliable exploration by researchers [9−18]. Therefore, developing new and effective fabrication methods to synthesize these heterostructures with well-defined clean surface and interfaces is crucial [19−24].
In response, various well-developed fabrication techniques, such as molecular beam epitaxy (MBE), pulsed laser deposition (PLD), and chemical vapor deposition (CVD) have been successfully applied by the researchers to synthesize the expected vertical stacked heterostructures [25−28]. The MoS2-graphene hybridization system, representative of these composites, not only features two quintessential two-dimensional materials but also demonstrates potential in photonic devices, energy catalysis, and batteries [29−40]. Recent researches have progressively shifted from traditional exfoliation and transfered to direct synthetic approaches involving CVD and MBE [41−47]. However, in the reported construction of the MoS2-graphene model structures, the graphene film still needs to be transferred to a substrate, which inevitably introduces interface impurities. Moreover, when fabricating the MoS2/HOPG stacking structure, the two-dimensional structure of graphene can hardly be maintained [48]. Although some studies have employed a combination of ultra-high vacuum growth technology and CVD to develop the MoS2-graphene model, the produced graphene often exhibits uneven thickness and quality on the substrate surface [49], potentially affecting the properties of the composite when combined with MoS2.
In this study, we focused on the fabrication of an ideal MoS2-graphene stacking heterostructure. Employing ultra-high vacuum (UHV) methods and precise temperature control, we first prepared high-quality, uniform graphene films on the SiC substrate and then grew MoS2 on the graphene/SiC surface via ambient CVD. Through a series of characterizations, we clearly confirmed the clean surface and interfaces of the as-prepared MoS2-graphene/SiC heterostructures. Moreover, we identified two growth modes of MoS2 on graphene/SiC, i.e. the formation of typical 2D triangular structures and a unique vertically spiral structure of MoS2. Particularly, our scanning tunneling microscopy (STM) study clearly resolved the atomic lattice of the spiral MoS2 and observed a reduced bandgap down to around 1.0 eV. Our research successfully demonstrated a clean synthetic approach combining UHV-MBE with ambient CVD, which may be widely applied for fabricating various 2D heterostructures with different compositions. The prepared MoS2-graphene/SiC model system also registers a promising platform for potential researches in the field of photonic devices, energy applications, and valleytronics.
-
The SiC substrates were purchased from Shanghai Jiadan Electronic Information Co., Ltd. Sulfur powder (99.6%) and MoO3 powder (99.6%) were purchased from Aladdin Co., Ltd. All of the chemicals above were used as received without further treatment.
-
Graphene-SiC substrate was prepared by three steps: (1) heating an ex situ SiC substrate in ultrahigh vacuum (UHV) for 2–6 h at ~650 °C, (2) preparing the silicon rich (3 × 3) phase in a Si flux phase at ~1000 °C, (3) heating the silicon rich (3 × 3) phase at ~1300 °C.
-
To achieve the CVD growth of MoS2 on graphene/SiC substrates, a specific experimental setup using a dual-zone tube furnace (OTF-1200X, Hefei Kejing Material Technology Co., Ltd.) was employed. The CVD process began by placing the precursors, sulfur (S) and molybdenum trioxide (MoO3), in separate quartz boats within the upstream and downstream zones of the furnace, respectively. The graphene/SiC substrate was strategically positioned facing down, supported by a specially designed holder to optimize the deposition of MoS2. The reaction chamber was first purged with high-purity nitrogen gas (N2) at a flow rate of approximately 300 standard cubic centimeters per minute (sccm) to ensure a clean environment free of contaminants. Following the purge, the temperature for the sulfur powder was gradually raised to 200 °C to initiate vaporization. The flow rate of nitrogen was then reduced to about 16 sccm to transport the sulfur vapor to the reaction zone where the MoO3 was located. Concurrently, the MoO3 powder was heated to 730 °C, facilitating its vaporization and subsequent reaction with the sulfur vapor. After the reaction period, the heating power was turned off, and the furnace was maintained closed until the internal temperature decreased to approximately 570 °C. At this point, the furnace cover was opened, allowing the system to cool naturally to room temperature under a restored nitrogen flow of 300 sccm to obtain the MoS2-graphene/SiC samples.
-
STM was measured with a commercial low-temperature STM (Unisoku 1400) at liquid nitrogen temperature at a base pressure of 1 × 10–10 Torr. The constant-current mode of scanning was adopted. Pt-Ir tips calibrated on single-crystal Au(111) surface were used for the scan. The scanning tunnelling spectroscopy (STS) measurements were performed with the Nanonis lock-in amplifier set with the oscillation frequency of 1000 Hz and the amplitude of 10 mV.
-
The AFM measurement was performed on the Dimension Icon (Bruker Co.) in air. SEM measurements were performed using a SU8220 model instrument. Raman spectroscopy was measured using a LabRam HR Evolution with incident laser of 532 nm for the wavelength.
-
As shown in FIG. 1, this study developed a series of precise preparation strategies that combine UHV-MBE techniques with ambient CVD methods to synthesize high-quality, clean-surfaced MoS2-graphene heterostructures. Initially, SiC was chosen as the initiative substrate. Under ultra-high vacuum conditions, the substrate was precisely heat-treated to remove silicon atoms from the surface, utilizing the residual carbon source to uniformly grow bilayer graphene film [50]. Rapid flash annealing at high temperatures (1300 °C), akin to conventional Si flash annealing [51], ensures uniform desorption of Si atoms, high nucleation density of carbon atoms, and consistent SiC decomposition rates at each SiC bilayer step. This process ultimately yields uniform bilayer graphene with a regular step structure. Subsequently, this graphene/SiC sample served as the growth substrate in a CVD tube furnace set at 730 °C. Nitrogen gas was used as both the carrier and protective atmosphere, transporting sulfur powder from the cooler zone to react with MoO3 in the hotter zone, thereby facilitating the growth of MoS2 on the graphene/SiC substrate. It is noteworthy that during the growth process, the graphene-coated substrate was inverted and placed in a quartz boat to optimize the quality and interface cleanliness of the MoS2 layer.
-
Following the synthesis approach depicted in FIG. 1, we successfully fabricated bilayer graphene on a SiC substrate. The surface structure characterization, shown in FIG. 2(a), revealed distinct atomic step. Notably, the original SiC substrate did not exhibit any atomic substrate, a phenomenon observed during the growth of graphene, indicating that we have successfully prepared a graphene/SiC growth substrate with an atomically flat surface.
Detailed characterization of the surface atomic structure (see FIG. 2(b)) demonstrated a clear hexagonal lattice with a lattice spacing of approximately 0.25 nm, confirming the high-quality graphene structure. Given the localized nature of STM measurements, Raman spectrum was employed to further characterize the growth substrate, as depicted in FIG. 2(c). The principal Raman peaks were located at 1497 cm−1, 1577 cm−1, 1666 cm−1, 1685 cm−1, and 2713 cm−1. Peaks at 1497 cm−1, 1666 cm−1, and 1685 cm−1 are attributed to the SiC substrate, while those at 1577 cm−1 and 2713 cm−1 correspond to graphene vibrations for G and G′ [49], respectively.
To further assess the uniformity of the sample, mapping imaging of the G′-band location (2713 cm−1) was performed, as shown in FIG. 2(d). This imaging revealed a relatively uniform intensity of the D-band signal across a larger scale, verifying the uniformity of the prepared graphene. Thus, combining STM and Raman spectroscopy, we have confirmed the successful preparation of a clean and atomically flat graphene/SiC interface for the growth of MoS2.
-
Following the successful synthesis of atomically thin, uniformly distributed graphene using ultra-high vacuum techniques, we extended our research to the chemical vapor deposition (CVD) growth of MoS2 on graphene/SiC substrates. In our experimental setup, the graphene/SiC substrates were positioned inversely, with the MoO3 precursor placed upstream in the airflow. This configuration resulted in a heterogeneous distribution of MoO3 on the graphene surface during growth, which facilitated the formation of MoS2 with variable thicknesses and morphologies. Interestingly, our experiments revealed two distinct growth modes of MoS2 on the graphene/SiC substrate, which we detail below. Initially, as depicted in FIG. 3(a), triangular MoS2 nanoflakes were synthesized, measuring approximately ~400 nm to ~500 nm across. Atomic force microscopy (AFM) characterization of these nanoflakes, shown in FIG. 3(b), demonstrates a triangular surface morphology on the monolayer MoS2-graphene/SiC samples. Furthermore, the graphene/SiC substrate’s surface atomic steps were exceptionally well-preserved. The height of these triangular nanoflakes, as presented in FIG. 3(b), was approximately 0.67 nm, consistent with the thickness of a MoS2 monolayer as reported in the literature. Additionally, Raman spectroscopy of the monolayer MoS2-graphene/SiC samples was performed, revealing distinctive vibrational peaks at 385.98 cm−1 and 405.89 cm−1, corresponding to the
${\mathrm{E}}^1_{2{\mathrm{g}}} $ and A1g phonon modes of MoS2, respectively. The peak separation of 19.91 cm−1, slightly less than 20 cm−1, provides further confirmation of the monolayer structure. These comprehensive characterizations underscore the successful fabrication of clean, atomically flat monolayer MoS2-graphene/SiC samples.Additionally, another intriguing growth outcome we observed is the formation of two-dimensional spiral MoS2, demonstrating that spiral MoS2 can directly grow on graphene/SiC substrates. The SEM image in FIG. 3(d) reveals a uniform surface of the spiral MoS2. Upon zoom in examination (see inset of FIG. 3(d)), variations in the surface contrast indicate the presence of height irregularities. Further characterization using atomic force microscopy (AFM), shown in FIG. 3 (e) and (f) for height and phase imaging respectively, distinctly illustrates the atomic steps in the surface’s spiral structure. Height measurements along a segment highlighted in FIG. 3(e), along the yellow line in FIG. 3(e, f), reveal continuous atomic steps with an approximate height of 0.69 nm, corresponding to the thickness of a MoS2 monolayer. This finding leads us to believe that we have successfully fabricated a structure of spirally grown MoS2 on graphene/SiC substrates, characterized by layer-by-layer growth with monolayer thickness. To further confirm the formation of MoS2, we performed Raman spectroscopy, as detailed in FIG. 3(g). This analysis revealed characteristic MoS2 peaks; detailed examination (see inset of FIG. 3(g)) showed the
${\mathrm{E}}^1_{2{\mathrm{g}}} $ and A1g phonon modes at 383.45 cm−1 and 407.31 cm−1, respectively, with a peak separation of 23.86 cm−1, indicative of a multilayer spiral structure. Notably, the typical vibrational peaks of graphene were absent. An expanded analysis of the G′ peak location, as presented in FIG. S1(a) (Supplementary materials, SM), identified this as the 1.92 eV photoluminescence peak of MoS2. Comparisons of other vibrational peaks in FIG. 3(g) with those in FIG. S1(b) (SM) from the post-growth blank graphene/SiC substrate confirmed their origin from the substrate itself. Thus, we confirm the successful preparation of a spirally grown, atomically flat, two-dimensional MoS2 nanostructure.Based on the comprehensive analysis presented, we can conclusively assert that we have effectively completed the synthetic pathway detailed in FIG. 1. Our study not only successfully fabricated a model system of monolayer MoS2 on graphene/SiC substrates, but also verified that MoS2 can undergo monolayer thickness-controlled, layer-by-layer spiral growth on atomically flat, clean, and uniform graphene/SiC substrates. This process culminated in the formation of spiral two-dimensional MoS2, showcasing the intricate control of our synthetic technique. What’s more, the synthesis method combining ultra-high vacuum with chemical vapor deposition has also been validated as an effective approach for preparing clean, atomically flat surfaces.
-
After employing SEM and AFM surface microscopy techniques combined with Raman spectroscopy to characterize MoS2-graphene/SiC samples, we have essentially confirmed the preparation of triangular MoS2 and spiral MoS2 samples. Considering the lack of practical examples of spiral MoS2 in the research literature, we will focus on its characterization using STM. The schematic diagram of the STM test is shown in FIG. 4. Through scanning, we found that more detailed surface structural information similar to FIG. 3(d–f) could be obtained via STM, as shown in FIG. 4(a, b). It allows for meticulous imaging of individually spiral grown MoS2, with the height of the MoS2 layers on spiral MoS2 being approximately ~0.69 nm. This side view confirms its layer-by-layer growth pattern akin to single-layer MoS2. Interestingly, despite the relatively large thickness due to spiral growth of MoS2, we can still observe the surface atomic steps of the graphene/SiC substrate through the MoS2 film (FIG. S2 in SM also reflects the trend of substrate step height), indicating that rotated MoS2 exhibits the same step trend as the substrate, implying a conformal growth between the two, demonstrating that the ultra-high vacuum-assisted CVD method we adopted can indeed prepare high-quality MoS2-graphene/SiC samples.
Furthermore, we also studied its atomic structure, as shown in FIG. 4(c), which is a lattice characterization of the layer-by-layer grown spiral MoS2. The clear hexagonal structure can be observed from the figure, and lattice measurements show a lattice length of ~0.32 nm, consistent with the standard lattice size of MoS2, indicating good quality of the spiral MoS2 prepared, which can support STM studies. Subsequently, we conducted preliminary exploration of the electronic structure of this spiral MoS2, as shown in FIG. 4(d). The STS spectrum of spiral MoS2-graphene/SiC samples clearly shows a valence band edge of approximately −0.85 eV and a conduction band edge of ~0.15 eV. This indicates that the spiral MoS2 we prepared still exhibits the characteristics of an N-type semiconductor, and due to the increase in thickness, its band gap decreases to ~1.0 eV compared to single-layer MoS2. This change in band gap is caused by the transition from a direct band gap to an indirect band gap due to the increase in thickness of MoS2.
Thus, we can demonstrate that the MoS2-graphene/SiC samples prepared by ultra-high vacuum combined with high-temperature CVD can be considered as model systems with high surface quality. This also provides a research example for the construction of other model systems.
-
In summary, our objective was to fabricate a model system comprising clean, atomically flat MoS2-graphene interfaces. Starting with a SiC substrate, we utilized a combination of ultra-high vacuum techniques and chemical vapor deposition to prepare graphene as the growth substrate for MoS2. This approach successfully facilitated the epitaxial growth of two distinct MoS2 structures on the atomically flat graphene surface. Our comprehensive characterization using SEM, AFM, and Raman spectroscopy verified the formation of monolayer triangular MoS2 nanoflakes and spiral MoS2 structures that grow layer-by-layer starting from a monolayer base. The surface morphology and structural characterizations confirmed their cleanliness and atomic-level flatness, setting a favorable stage for subsequent scanning tunneling microscopy (STM) analysis. Further STM investigations provided detailed insights into the surface atomic arrangements. We confirm the microstructure of the spiral triangles on graphene/SiC using STM, and obtain the surface electronic band gap of ~ 1.0 eV. This hybrid vacuum and CVD method exemplifies an effective strategy for constructing high-quality, interface-rich MoS2/graphene/SiC model systems.
Supplementary materials: Additional characterization results including Raman and STM measurements for samples.
Fabrication and STM Characterization of Spiral MoS2-Graphene/SiC Heterostructure
- Received Date: 01/06/2024
- Available Online: 27/08/2025
-
Key words:
- Spiral MoS2 /
- Heterostructure /
- Molecular beam epitaxy /
- Chemical vapor deposition /
- Scanning tunneling microscope
Abstract: Two-dimensional (2D) heterostructures comprising of differently stacking atomic layers are attractive owing to its flexible composition as well as the emerging new physicochemical properties. However, so far many 2D vertical heterojunctions are constructed through transfer methods, inevitably introducing interfacial impurities and thus hindering detailed atomic-level studies. In this work, we have developed a clean two-step fabrication strategy by combining ultrahigh vacuum (UHV) molecular beam epitaxy (MBE) growth with ambient chemical vapor deposition (CVD). We firstly grew single crystalline graphene film on a SiC substrate under UHV condition, and then synthesized MoS2 films on the graphene-SiC surface through CVD under inert atmosphere, thus successfully realized the construction of a well-defined MoS2-graphene/SiC heterojunction with clean surface. Particularly, we observed the MoS2 can not only grow into monolayer flakes but also form spiral structures, the latter showing layer-by-layer stacks with reduced bandgap down to ~1.0 eV.
首页
登录
注册


DownLoad: