2026 Volume 35 Issue 4
Article Contents

Kelun Zhao, Jiaming Zhou, Yanqing Zhang, Qiang Kang, Yang Liu, Xinyi Li, Chaoming Liu, Tianqi Wang, Mingxue Huo. The 1-MeV electron irradiation effect and damage mechanism analysis of GaInP/GaAs heterojunction solar cells[J]. Chinese Physics B, 2026, 35(4): 048801. doi: 10.1088/1674-1056/ae0638
Citation: Kelun Zhao, Jiaming Zhou, Yanqing Zhang, Qiang Kang, Yang Liu, Xinyi Li, Chaoming Liu, Tianqi Wang, Mingxue Huo. The 1-MeV electron irradiation effect and damage mechanism analysis of GaInP/GaAs heterojunction solar cells[J]. Chinese Physics B, 2026, 35(4): 048801. doi: 10.1088/1674-1056/ae0638

The 1-MeV electron irradiation effect and damage mechanism analysis of GaInP/GaAs heterojunction solar cells

  • Received Date: 10/07/2025
    Accepted Date: 18/08/2025
    Available Online: 01/04/2026
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Figures(9)  /  Tables(3)

Article Metrics

Article views(297) PDF downloads(0) Cited by(0)

Access History

The 1-MeV electron irradiation effect and damage mechanism analysis of GaInP/GaAs heterojunction solar cells

Abstract: This study explore the radiation damage effects on GaInP/GaAs heterojunction (HJT) solar cells when subjected to 1-MeV electron irradiation. Light I–V measurements show that Voc, Jsc, and Pmax of the cells exhibit a logarithmic degradation pattern with increasing electron irradiation fluence. Under identical irradiation conditions, the degradation of Jsc is substantially less pronounced than that of Voc. Under the same conditions, the heterojunction cell shows better radiation resistance, mainly as its Voc degradation rate with fluence increase is lower than the homojunction cell. Spectral response analysis reveals that 1-MeV electron radiation mainly causes longwave zone damage in the GaInP/GaAs HJT cells, which intensifies as irradiation fluence accumulates. Dark characteristic analysis indicates that both recombination and diffusion currents in the cells rise with increasing irradiation fluence, with recombination current dominating the dark current. Deep level transient spectroscopy tests show that 1-MeV electron irradiation introduces four defects (H1–H4) in the cells, located at H1 (Ev + 0.717 eV)/H1∗ (Ev + 0.744 eV), H2 (Ev + 0.369 eV), H3 (Ev + 0.282 eV), and H4 (Ev + 0.032 eV). Among these, the concentration H1 of defects increases most drastically with fluence and directly correlates with the rapid degradation of cell performance under high fluence, making it the crucial factor responsible for the swift degradation of GaInP/GaAs HJT cells under high fluence 1-MeV electron irradiation.

1.   Introduction
  • In the past half century, solar cells have become a main energy source for space exploration spacecraft since NASA first applied photovoltaic technology to satellites. As human exploration extends to deep space, space-specific solar cells face challenges from extreme environments like temperature cycles and radiation.[1–4] Recent progress in photovoltaic materials, such as wider temperature adaptability and better radiation resistance,[5–7] has driven high conversion efficiency photovoltaic arrays forward remarkably. Advanced photovoltaic systems, with great radiation resistance and long term stability, are key for space exploration power.[8–10] Among photovoltaic tech, III–V group solar cells, particularly GaAs ones, are crucial in multi-junction cells and widely used in spacecraft power systems due to their radiation resistance and adaptability.[11,12] Research shows that for GaInP/GaAs/Ge three-junction solar cells, radiation damage mainly affects the GaAs sub-cell, whose fast degradation limits the overall cell efficiency.[13–15] 1-MeV electron irradiation causes the EOL Jsc of the GaAs sub-cell in the GaInP/GaAs double-junction cell to drop to 83% of its initial value,[16,17] in the GaInP/GaAs/Ge triple-junction cell, the EOL Jsc retention rate of its GaAs sub-cell reaches 93%.[18,19] As space exploration missions grow more demanding, solar cells need better performance, especially stability in high energy particle radiation. Recently, heterojunction solar cell technology has gained attention for optimizing GaAs solar cell design to meet these complex space mission needs.

    GaInP/GaAs HJT solar cells, a promising photovoltaic tech, leverage high/low bandgap semiconductor interfaces for a simple hetero p–n junction. Their excellent passivation contact and stability make them a likely next-gen mainstream product.[20,21] They outperform homojunction cells in efficiency due to dark current’s exponential drop with p–n junction bandgap rise, driven by non-equilibrium carrier recombination and non-radiative SRH recombination. This phenomenon impacts the open-circuit voltage more than the short-circuit current, thereby enhancing the cell’s efficiency.[22] KL Schulte’s team modeled and simulated GaAs heterojunction solar cells, finding that emitter doping and band offset are key for efficiency. They designed a GaAs/GaInPAs cell via HVPE with 27% efficiency under AM1.5 (1 Sun).[22] Antonio Marti’s modeling showed heterojunction cells’ open-circuit voltage can exceed the low-bandgap semiconductor’s bandgap under finite carrier mobility.[23] Hwang et al. built an AlGaAs/GaAs cell with a logarithmic bandgap grading layer, achieving 28.7% efficiency via AFORS-HET optimization. This proved collaborative heterojunction and bandgap grading layer design boosts solar cell performance.[24] In space, abundant free charged particles are bound by planetary magnetic fields, forming radiation belts. Solar cells on orbiting spacecraft are exposed to radiation from these particles, causing a decline in their electrical performance.[25–31] Wang et al. used DLTS to study GaInP/GaAs/InGaAs IMM3J solar cells after 1-MeV electron irradiation. They found GaAs sub-cell defects at Ev + 0.36 eV/Ev + 0.42 eV and InGaAs sub-cell defects at Ev + 0.29 eV/Ev + 0.24 eV. DLTS results showed effective minority carrier lifetime in GaAs/InGaAs cells decreased with increasing irradiation fluence.[19] Zhou et al. used DLTS to study InGaAs (1.0 eV/0.7 eV) cells in IMM4J solar cells after 5-MeV proton irradiation. They found radiation introduced H (Ev + 0.09 eV) and H1 (Ev + 0.07 eV) hole traps, with defect concentrations increasing with higher fluences.[31] These research findings underscore the significance of gaining a deep understanding of radiation damage mechanisms for optimizing solar cell structures and enhancing their radiation resistance.

    To conduct an in-depth analysis of the radiation resistance performance of GaInP/GaAs heterojunction solar cells. In this work, this paper conducts 1-MeV electron radiation experiments on cells at varying fluences, simulating space radiation conditions. Using optical IV (LIV), external quantum efficiency (EQE), dark characteristics (DIV), and deep-level transient spectroscopy (DLTS) techniques, the study analyzes the cells’ electrical, spectral degradation, and defect evolution before and after radiation.

2.   Experiment
  • GaInP/GaAs heterojunction (HJT) solar cell with a size of 0.6 cm×0.6 cm was epitaxially grown on GaAs substrate using the metal organic chemical vapor deposition (MOCVD) technique. The structural schematic is shown in Fig. 1. The emitter region comprises high bandgap GaInP, while the base region consists of low bandgap GaAs. To mitigate the adverse effects of band discontinuity at the heterojunction interface on carrier drift, the emitter was heavily doped during growth to enhance the depletion region electric field. Additionally, a window layer and a back surface field (BSF) layer were incorporated to improve spectral utilization and carrier collection efficiency. Figure 2 shows the I–V characteristic curve of the GaInP/GaAs HJT solar cell before radiation under the standard test environment (AM0, 135.3 mW/cm2, 25 ± 2 °C). This curve directly reflects the initial photovoltaic performance parameters of the GaInP/GaAs HJT solar cell, including a short-circuit current (Isc) of 11.07 mA, an open-circuit voltage (Voc) of 1.01 V, and a maximum power (Pmax) of 8.65 mW. Based on these parameters, the power conversion efficiency of the GaInP/GaAs HJT solar cell is 17.8%, fully demonstrating its excellent energy conversion performance.

    This study conducted irradiation experiments on GaInP/GaAs HJT solar cells using 1-MeV electron accelerator at the Heilongjiang Institute of Nuclear Energy. At room temperature, irradiation experiments were carried out on GaInP/GaAs HJT cells with radiation fluxes of 1 × 1011 cm−2⋅s−1 and fluences of 1 × 1014 cm−2, 3 × 1014 cm−2, 5 × 1014 cm−2, 8 × 1014 cm−2, and 1 × 1015 cm−2 at 1-MeV electrons. Following irradiation, samples underwent 3-day RT annealing. Post-annealing electrical performance was measured under standard test conditions (AM0, 135.3 mW/cm2, 25 ± 2 °C). Spectral response (external quantum efficiency, EQE) was measured as a function of irradiation fluence, and the scanning step size of the QE test is 5 nm. Dark current–voltage (DIV) characteristics, measured via the four-probe method to minimize series resistance effects, were fitted with a double-exponential diode model to extract recombination parameters. Deep level transient spectroscopy (DLTS) was employed to analyze defect evolution post-irradiation. In the DLTS test, the reverse bias voltage UR was set to 5 V, the pulse voltage Up was set to 0.1 V, the pulse width tp was set to 0.2 ms, and tw was set to 19.2 ms, 192 ms, and 1.92 s.

3.   Results and discussion
  • Figure 3(a) presents the light I–V characteristic curve of the GaInP/GaAs HJT solar cell after 1-MeV electron irradiation. From the figure, it can be seen that at room temperature, the 1-MeV electron irradiation causes a certain degree of damage to the electrical performance of the cell, and the degree of damage is positively correlated with the irradiation fluence. As the irradiation fluence increases, the degradation of the cell’s electrical performance becomes more significant. This is because the number of displacement defects generated during the 1-MeV electron radiation increases rapidly with the increase in the irradiation fluence, thereby accelerating the recombination rate of photogenerated electron–hole pairs and leading to a significant decline in the cell’s electrical performance. To present the damage effect of electron irradiation on the solar cell more intuitively, this paper normalizes the key parameters of the solar cell (Jsc, Voc, Pmax). A large number of studies have shown that the degradation of the solar cell’s electrical performance has a logarithmic relationship with the irradiation fluence.[24,25] The degradation follows the empirical model

    where P represents the normalized electrical performance parameter; cp is the performance degradation rate, which is usually limited to a dimensionless constant within the range of 0–1 during the fitting process; φ0p is the critical fluence, which is related to the intrinsic properties of the solar cell and the type of irradiation particle energy.

    Figure 3(b) presents the normalized degradation curves of the three main electrical parameters for the GaInP/GaAs HJT solar cell post 1-MeV electron irradiation, with fitting parameters in Table 1.

    Equation (1) can fit the cell’s electrical damage and output pattern well, with a coefficient of determination (R2) above 0.99. The results show a positive correlation between the degradation of these parameters and the radiation fluence. At the same fluence, Voc degrades more than Jsc. As shown in Table 1, the critical fluence of Jsc is 62 times that of Voc. So, rapid Voc attenuation is a key factor in the cell’s performance degradation. When the cumulative irradiation fluence reaches 1 × 1015 cm−2, further analysis shows that the Jsc, Voc, and Pmax of the GaInP/GaAs HJT solar cell degrade to 86.9%, 88.1%, and 78.6% of the initial values respectively. Notably, Pmax degrades fastest as radiation fluence increases, since it’s jointly impacted by Voc and Jsc degradation. Despite this, the GaInP/GaAs HJT solar cell’s power conversion efficiency remains at 13.8%, indicating its excellent radiation resistant performance.

    Figure 4 compares the open-circuit voltage degradation trends of GaAs heterojunction and homojunction solar cells after 1-MeV electron irradiation. Under the same conditions, the heterojunction cell shows better radiation resistance, mainly as its Voc degradation rate with fluence increase is lower than the homojunction cell. The heterostructure shifts part of the p–n junction depletion region to high-bandgap GaInP, lowering the SRH recombination rate.[18] This inhibition reduces the Voc degradation trend with radiation fluence increase, enhancing the cell’s radiation resistance.

  • Figure 5(a) presents the spectral response curves of GaInP/GaAs HJT solar cells after irradiation with different fluences of 1-MeV electrons. As the fluence increases, the EQE decreases overall. Analysis of the spectral response degradation reveals that the radiation damage primarily manifests as reduced response in the long-wavelength band, with the degradation magnitude increasing with fluence. The 1-MeV irradiation energy is sufficient to generate displacement damage in GaInP/GaAs HJT solar cells. Given that the penetration depth of 1-MeV electrons exceeds the cell thickness, the damage distribution in the active region is uniform.[13,27] Based on the structure, where the GaAs base region is ∼100 times thicker than the GaInP emitter, the damage is concentrated primarily in the GaAs base. As GaAs is a direct-bandgap semiconductor, photons penetrate deeper at longer wavelengths. Thus, photogenerated carriers produced by long-wavelength photons originate farther from the junction. This increases the probability of carrier capture by defects, explaining the long-wavelength band degradation observed.

    Photocurrent density (Jph), a key parameter for evaluating solar cell performance and material properties, is obtained from spectral response measurements. Figure 5(b) shows the normalized Jph as a function of 1-MeV electron irradiation fluence. After irradiation, the degradation of Jph is well described by Eq. (1), with the R2 above 0.99. The fitting results reveal that the electrical performance degradation rate cp of the Jph fitting curve is 0.23, and the critical fluence is 3.63 × 1014 cm−2. As shown in Fig. 5(b), as the irradiation fluence increases, Jph degrades slowly initially; however, once the fluence exceeds 3.63 × 1014 cm−2, the degradation rate increases significantly. When the irradiation fluence reaches 1 × 1015 cm−2, Jph still retains 87% of the initial performance of the GaInP/GaAs HJT solar cell. This further demonstrates that GaInP/GaAs HJT solar cells possess excellent radiation resistance performance.

  • To eliminate the interference of photogenerated carriers and deeply reveal the damage mechanism of GaInP/GaAs HJT solar cells under 1-MeV electron irradiation, and to quantitatively analyze the performance degradation law before and after irradiation, this study uses a double-exponential model to fit and analyze the dark characteristic curve. This model splits the reverse saturation current into two components: diffusion current (Jdiff) and recombination current (Jrec), thereby more effectively characterizing the intrinsic performance of the solar cell. The equation is expressed as

    Among them A1 = n1/KT, A2 = n2/KT, n1 and n2 represent the diffusion ideality factor and the recombination ideality factor respectively. Series resistance (Rs) and shunt resistance (Rsh) represent the series and parallel resistive losses, respectively. Measurements using the four-probe method minimized contact and series resistance effects, ensuring consistency across the batch of GaInP/GaAs HJT solar cells studied. Before and after irradiation measurements showed Rs < 0.1 Ω⋅cm2 and Rsh > 106 Ω⋅cm2. Therefore, in this experiment, Rs and Rsh were not the main influencing factors of the dark current of the solar cell, and they were ignored in the subsequent analysis. Figure 6 shows the DIV of GaInP/GaAs HJT solar cells under different irradiation fluences of 1-MeV electrons. From the figure, two typical features can be observed: (i) When the scanning voltage is lower than the forward turn on voltage, the current remains at a low level; (ii) After the voltage crosses the forward turn on threshold, the current increases linearly, indicating that the device enters the low resistance working region. It is worth noting that as the electron irradiation fluence increases, the dark characteristic curve shifts overall towards lower voltage and higher current. This indicates that with the increase of irradiation fluence, the dark current increases significantly under the same forward bias voltage.

    To simplify curve fitting and enhance accuracy, the diffusion ideality factor n1 was set to 1. Table 2 lists the fitted parameters of the DIV curves under various irradiation fluences obtained from the double-exponential model. Figure 7 reveals the trends of diffusion current Jdiff and recombination current Jrec with irradiation fluence. From Fig. 7(a), Jdiff increases significantly with rising irradiation fluence. This stems from irradiation induced reduction in minority carrier diffusion length (Lp) which directly elevates Jdiff. Since Jdiff is governed by carrier recombination within a characteristic distance Lp from the space charge region edge,[32] defect accumulation near the junction enhances recombination, further increasing Jdiff. Under 1-MeV electron irradiation, GaInP/GaAs HJT solar cells show uniform radiation damage defect distribution. With the introduction of irradiation defects, the effective number of minority carriers that can migrate to the junction region is reduced, resulting in a decrease in the short-circuit current. This mechanism is highly consistent with the Jsc change trend shown in Fig. 3, revealing that the abnormal increase in diffusion current is one of the key factors causing the degradation of the short-circuit current. Figure 7(b) experimentally shows a strong positive correlation between Jrec and 1-MeV electron irradiation fluence. This current component originates from Shockley–Read–Hall (SRH) nonradiative recombination via defects in the space charge region.[33] Under 1-MeV electron irradiation, the space charge region defect concentration rises with fluence, amplifying recombination center density. These centers reduce minority carrier lifetime (τ) through enhanced SRH recombination, thereby elevating Jrec. Further analysis reveals that when the radiation fluence reaches 1 × 1015 cm−2, the Jdiff and Jrec of the GaInP/GaAs heterojunction are approximately increased to 130 times and 1.6 times of the initial values, respectively. The maximum Jdiff is of the order of 10−17, and the maximum Jrec is of the order of 10−9. Jrec is more than 108 times that of Jdiff. Thus, after 1-MeV electron irradiation, the dark current of the GaInP/GaAs heterojunction solar cell is dominated by the recombination current.

  • In solar cells, SRH recombination is the main factor affecting the diffusion of excess carriers. Defects induced during fabrication and irradiation act as recombination centers, accelerating SRH recombination, thus reducing carrier lifetime and degrading cell performance. Therefore, accurately characterizing the energy levels, concentrations and capture cross-sections of these defects is of great significance for deeply understanding the performance degradation of radiation-induced solar cells. The DLTS technique based on the capture and emission processes of carriers by deep-level traps, and through systematic temperature scanning and rate window analysis, can quantitatively measure and analyze key parameters such as the energy level positions, concentrations, and capture cross-sections of the defects.[34,35] So, in this study, we conducted systematic DLTS tests on GaInP/GaAs HJT solar cells under different irradiation fluences.

    Figure 8 shows the evolution of the DLTS spectra for the GaInP/GaAs HJT solar cell measured between 20 K–380 K as a function of irradiation fluence. The defect characteristics change significantly with fluence, manifested primarily by differing growth rates in the intensities of the characteristic defect peaks. Given that the sample structure used in this study is n+p, the majority carriers in the low-doped base region are holes, so the four characteristic defect peaks shown in the figure all correspond to hole defects, and their energy levels are located above the valence band top. The DLTS analysis results show that 1-MeV electron irradiation conditions mainly introduce four characteristic hole defect peaks (H1–H4) in the GaInP/GaAs HJT solar cell. Their energy level positions are presented in Table 3: H1 (Ev + 0.717 eV)/H1∗ (Ev + 0.744 eV), H2 (Ev + 0.369 eV), H3 (Ev + 0.282 eV), and H4 (Ev + 0.032 eV). Further analysis revealed that the concentrations of all defects increased with the increase in irradiation fluence. Among them, the growth rate of H1 defect concentration was significantly higher than that of other defect types (H2, H3, H4). When the radiation fluence reached 5 × 1015 cm−2, the concentration of H1 defects rose to 7.11 × 1014 cm−3, while the concentrations of H2, H3, and H4 defects respectively were 3.32 × 1013 cm−3, 3.85 × 1013 cm−3, and 2.84 × 1013 cm−3. At this irradiation fluence, the concentration of H1 defects was approximately 20 times that of other defect concentrations, indicating that the defects introduced by high-fluence 1-MeV electron irradiation were mainly H1 defects. Moreover, by fitting with the Arrhenius formula (Fig. 9), the capture cross-section σ of H1 defects reached 1.78 × 10−12 cm2, which was much higher than that of other defect types. The substantial increase in H1 concentration and its efficient recombination characteristics are thus a key factor in the rapid degradation of GaInP/GaAs HJT solar cells under high-fluence 1-MeV electron irradiation. As an efficient SRH recombination center, H1 reduces carrier lifetime and diffusion length, diminishing the collection of photogenerated carriers. This leads to a significant increase in recombination current with irradiation fluence, consistent with the DIV analysis. Consequently, in the phot I–V test, the phenomenon of the electrical performance of GaInP/GaAs HJT cells rapidly degrading with the increase in irradiation fluence is manifested.

    Based on the analysis of comprehensive literature data,[36,37] it was found that H3 (Ev + 0.282 eV) and H4 (Ev + 0.032 eV) in the GaInP/GaAs HJT cell might belong to the intrinsic point defect cluster. Their essence is that electron irradiation directly induces as lattice vacancies-interstitial atoms (VAs–IAs) through the displacement damage effect. Combined with the experimental results and theoretical analysis, H1 (Ev + 0.717 eV)/H1∗ (Ev + 0.744 eV), and H2 (Ev + 0.369 eV) might originate from the migration of As interstitial atoms (IAs) induced by irradiation, and form defect complexes combined with inherent impurities in the material.

4.   Conclusion and perspectives
  • This study systematically investigated the radiation damage effect of GaInP/GaAs HJT solar cells under different irradiation fluences of 1-MeV electrons at room temperature. Through LIV and EQE tests, the degradation laws of the cell’s electrical performance were analyzed. The results showed that the three key electrical performance parameters of the solar cell: open-circuit voltage (Voc), short-circuit current density (Jsc), and maximum output power (Pmax), followed the logarithm degradation law when subjected to the electron irradiation fluence. The rapid degradation of Voc is an important factor causing the degradation of solar cell performance. Under the same radiation conditions, the degradation amplitude of Jsc is significantly smaller than that of Voc, and the critical injection fluence of Jsc is 62 times that of Voc. And the heterojunction cell shows better radiation resistance, mainly as its Voc degradation rate with fluence increase is lower than the homojunction cell. The spectral response test results show that the radiation damage of 1-MeV electron to GaInP/GaAs HJT cells mainly manifests as long-waveband damage. The degradation amplitude increases with the accumulation of irradiation fluence, and the degradation process of photogenerated current density Jph shows a trend of first slow and then fast. DIV reveals that after 1-MeV electron irradiation, the dark characteristic curve presents two typical features, and both the recombination current and diffusion current have an increasing relationship with the irradiation fluence. After analysis, it is found that the dark current of GaInP/GaAs HJT cells is dominated by the recombination current. DLTS test reveals that after 1-MeV electron irradiation, four characteristic hole defect peaks (H1–H4) are mainly introduced into the GaInP/GaAs cells. Their energy level positions are calculated as H1 (Ev + 0.717 eV)/H1∗ (Ev + 0.744 eV), H2 (Ev + 0.369 eV), H3 (Ev + 0.282 eV), and H4 (Ev + 0.032 eV), and in the high fluence condition, the H1 defect is an important factor causing the rapid degradation of the solar cell.

Figure (9)  Table (3) Reference (37)

Catalog

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return