2026 Volume 35 Issue 4
Article Contents

Jiong Wu, Zhangyang Zhou, Li Zhu, Liushun Wang, Ming Du, Hongjun Wu, Qingwei Wang, Dahua Ren, Teng Zhang, Yongdan Zhu, Jinqiao Yi. Optical modulation and fabrication of two-dimensional VO2(M)-AgSiO2 shell/core composite photonic crystal structures[J]. Chinese Physics B, 2026, 35(4): 046802. doi: 10.1088/1674-1056/ae1569
Citation: Jiong Wu, Zhangyang Zhou, Li Zhu, Liushun Wang, Ming Du, Hongjun Wu, Qingwei Wang, Dahua Ren, Teng Zhang, Yongdan Zhu, Jinqiao Yi. Optical modulation and fabrication of two-dimensional VO2(M)-AgSiO2 shell/core composite photonic crystal structures[J]. Chinese Physics B, 2026, 35(4): 046802. doi: 10.1088/1674-1056/ae1569

Optical modulation and fabrication of two-dimensional VO2(M)-AgSiO2 shell/core composite photonic crystal structures

  • Received Date: 13/08/2025
    Accepted Date: 15/10/2025
    Available Online: 01/04/2026
通讯作者: 陈斌, bchen63@163.com
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索

Figures(5)  /  Tables(1)

Article Metrics

Article views(216) PDF downloads(1) Cited by(0)

Access History

Optical modulation and fabrication of two-dimensional VO2(M)-AgSiO2 shell/core composite photonic crystal structures

Abstract: The high phase transition temperature, low solar modulation efficiency, and unfavorable brown-yellow color have limited the practical application of VO2-based smart windows. By embedding a hexagonal close-packed monolayer array of SiO2 into the monoclinic VO2(M)–Ag composite film using an electron-beam evaporation system, a two-dimensional VO2(M)–AgSiO2 shell/core photonic crystal composite material was formed. Due to the increased contact area between Ag and VO2(M) within the composite material, the concentration of free electrons in VO2(M) increases, causing the phase transition to occur at a lower temperature of 52.2 °C. With the embedded SiO2 array, the solar modulation efficiency is enhanced to 25.4%, and the visible light modulation efficiency increases by nearly 7 times. Additionally, the grating effect of the photonic crystal significantly diffracts light around the 600 nm wavelength, reducing the strong absorption of VO2(M) in the shortwave range and diluting its inherent brown-yellow color. By embedding the SiO2 array into the VO2(M)–Ag composite film, this approach simultaneously achieves a reduction in phase transition temperature, enhancement of solar modulation efficiency, and color adjustment of the film, providing a reference for the practical application of VO2 in smart windows.

1.   Introduction
  • Smart windows play an essential role in building energy efficiency. In hot weather, they effectively block substantial sunlight; while in colder seasons, they allow solar energy to pass through, helping to regulate indoor temperatures.[1,2] Thermochromic smart windows, which adjust solar transmission based on temperature, have been extensively researched in recent years and have become an important component of green buildings. Vanadium dioxide (VO2) is a typical thermochromic material that undergoes an insulator-to-metal phase transition at approximately 341 K.[3–6] The transition is accompanied by a sharp decrease in infrared transmittance while maintaining high transmittance in the visible range.[6] Consequently, VO2-based thermochromic windows could significantly reduce solar heat gain at high temperatures without affecting indoor brightness.[3–5] However, the high transition temperature (Tc), low solar modulation efficiency (ΔTsol), and unfavorable brown-yellow color have limited the practical application of VO2-based smart windows.[3–8]

    Researchers have proposed various methods to address these challenges, including element doping,[9–11] composite structures,[12–16] porous structures,[17,18] multilayer structures,[19,20] and core-shell structures.[21–23] Elemental doping or compositing can effectively reduce the Tc, but this often comes at the expense of ΔTsol.[9–11] Fabricating VO2 in porous structures or adding anti-reflective layers can increase optical transmittance and enhance the ΔTsol, yet these approaches do not lower Tc and are further limited by complex fabrication processes.[12–20] Recently, Ke et al. embedded VO2 within a monolayer hexagonal array of SiO2 spheres to form a SiO2/VO2 core-shell structure. By adjusting the size of the SiO2 spheres, control over the film color and ΔTsol was achieved, but the Tc was not effectively reduced.[21] To date, low Tc, high ΔTsol and desirable color have yet to be simultaneously achieved, indicating a continued need for further research.

    A monolayer-based, two-dimensional periodic nanostructure of colloidal spheres can be viewed as a two-dimensional photonic crystal.[20–23] By adjusting the structural parameters of the photonic crystal, specific wavelengths of visible light can be inhibited, thereby altering the color of the material.[24–27] Furthermore, extensive research has demonstrated that incorporating noble metals (e.g., Pt, Ag) into VO2 films can lower Tc by increasing free electron density.[12,28–31] Consequently, combining a VO2–Ag composite film with a monolayer SiO2 colloidal sphere array might enable Tc reduction, improved ΔTsol, and better control over the film color.

    In this study, SiO2 nanoarrays were embedded into the monoclinic VO2(M)–Ag composite film using an SiO2 template and electron-beam evaporation system to study the optical properties of the composite film.

2.   Experimental details
  • A monolayer, dense SiO2 nanoarray was prepared using an improved interfacial self-assembly method (Figs. 1(a)–1(d)).[32,33] Briefly, the 0.3 wt% SiO2 colloidal spheres (500 nm) were dispersed in a 1:1 volume ratio mixture of deionized water and absolute ethanol, and then slowly dripped onto a water/air interface via drainage glass to form a single layer of dispersed SiO2 nanospheres (Fig. 1(a)). Then, several drops of 2 wt% sodium dodecyl benzene sulfonate solution were added to drive the floating SiO2 spheres to form a rainbow film (Fig. 1(b)). Next, the monolayer of SiO2 colloidal spheres was transferred onto a clean quartz substrate using a PTL-MMB01 dip-coating machine (Shenyang Kejing) at a lifting speed of 120 μm/min (Fig. 1(c)), and then we obtained the regulated SiO2 photonic crystal (Fig. 1(d)).

    The preparation methods of VO2 films have been previously reported.[12,34,35] The VO2 films were prepared using the electron-beam evaporation system at a base pressure 5.0 × 10−5 Pa. Under high vacuum conditions (working pressure 5 × 10−3 Pa), the VO2 target was placed in a crucible located ∼ 300 mm below the substrate holder and evaporated by an incident electron beam with an accelerating voltage of 10 kV. On a quartz substrate heated to 300 °C, a VO2 film with a thickness of 200 nm was grown at a deposition rate not exceeding 0.5 nm/s. For the preparation of composite films, a clean quartz substrate and a quartz substrate with an SiO2 array were simultaneously placed on the substrate holder. A 90 nm thick VO2 film was first deposited on both substrates using the same growth process. Then, an Ag layer with a thickness of 20 nm was deposited on both samples at a rate not exceeding 0.5 nm/s, followed by another 90 nm thick VO2 layer (Figs. 1(e) and 1(f)). Research shows that monoclinic VO2 (VO2(M)) films with a high (011) orientation in their insulating state exhibit excellent phase transition properties, making them highly suitable for smart coating applications.[36] To achieve optimal film quality, the growth process requires samples to undergo in-situ annealing at 500 °C and 10 Pa for 30 minutes. The final products, pure VO2(M), VO2(M)–Ag, and VO2(M)–AgSiO2 composites, are designated as samples S1, S2, and S3, respectively.

  • The surface morphology of the samples was characterized using a field-emission scanning electron microscope (FESEM, Carl Zeiss Supra VP55, Germany) at an accelerating voltage of 10 kV. The crystal structure of the samples was identified by grazing incidence x-ray diffraction (GIXRD, X’Pert Pro MPD, Netherlands) with Cu Kα1 radiation (λ = 0.15406 nm) at an incidence angle of 1°. Optical transmittance at a fixed wavelength of 2000 nm was measured during heating and cooling in the temperature range of 30 °C to 85 °C using a Shimadzu UV-3700 double-beam UV-Vis-NIR spectrophotometer (Japan) equipped with a temperature control device. Transmittance spectra at 25 °C and 90 °C and absorbance spectra at 25 °C were measured over the wavelength range of 350–2500 nm. The carrier concentration was determined at room temperature using single-magnetic-field (0.58 T) Hall measurements (Nanometrics HL5500PC, USA) based on the van der Pauw method.

  • The solar transmittance (Tsol, wavelength range 350–2500 nm) and visible light transmittance (Tlum, wavelength range 380–780 nm) of the samples were calculated using the following formulas:[13,17]

    while T(λ) represents the transmittance spectrum percentage at wavelength λ. φlum(λ) is the luminous efficiency function of the human eye under standard photopic vision, and φsol(λ) is the solar irradiance spectrum function at an air mass of 1.5 (equivalent to solar irradiance at a 37° angle above the horizon). The ΔTsol and visible light modulation efficiency (ΔTlum) can be calculated using[13]

3.   Results and discussion
  • Figure 2 shows the GIXRD diffraction patterns of the samples at room temperature. Sample S1 exhibits a VO2 film with a pure monoclinic phase and (011) crystal orientation, with diffraction peaks observed at 2θ ≈ 27.9°, 37.1°, 55.6°, and 57.5°, corresponding to the (011), (2¯11), (220), and (022) planes of VO2(M) (P21/c, JCPDS#65-2358), respectively.[35] No diffraction peaks from other vanadium oxides were detected, indicating that the film is single-phase within the sensitivity limits of the technique. After the addition of Ag (S2), new diffraction peaks appear at 2θ ≈ 38.2°, 44.4°, and 64.6°, corresponding to the (111), (200) and (220) planes of Ag (Fm3¯m, JCPDS#87-0720).[12] Following the incorporation of a monolayer hexagonal close-packed SiO2 nanosphere array (S3), a new broad peak emerges around 2θ ≈ 23°, corresponding to amorphous SiO2. The indicates that VO2(M)–Ag composite film was successfully deposited onto the SiO2 nanosphere array.

    Figures 3(a) and 3(b) present the microscopic nanostructures of samples S1 and S2, respectively, showing a uniform coating of VO2 nanoparticles on the quartz substrate. The S1 exhibits well-defined grains with fine cracks and an average grain size of approximately 35 nm. The distinctive structure enhances light transmission, thereby improving the optical properties of the VO2 film.[13] With the addition of Ag, the fine cracks are eliminated, resulting in a smooth and dense film surface, while the average grain size remains nearly unchanged. Analysis of the EDS spectra from the selected regions of the samples (Figs. 3(c) and 3(d)) reveals an additional resonance peak near 3 keV in Fig. 3(d), which is absent in Fig. 3(c). This new peak corresponds to Ag, confirming the successful incorporation of Ag into the VO2 thin film. Figure 3(e) shows the prepared SiO2 nanosphere array, with the nanospheres arranged in a densely packed hexagonal pattern, forming a monolayer structure on the quartz substrate. Each SiO2 sphere has a uniform diameter of 500 nm. The VO2(M)–Ag composite film was then deposited onto the SiO2 template, resulting in the VO2(M)–Ag–SiO2 composite film, as shown in Fig. 3(f). The VO2(M)–Ag composite film uniformly covers the upper portion of the SiO2 template. The inset in Fig. 3(f) further reveals that the composite material successfully penetrates into the lower spaces between the SiO2 spheres and the quartz substrate. Building on this, we successfully embedded a monolayer hexagonally close-packed SiO2 nanosphere array with a particle diameter of 500 nm into the VO2(M)–Ag composite, forming a VO2(M)–Ag–SiO2 shell/core structured composite.

    To investigate the effect of Ag and SiO2 arrays on the phase transition temperature (Tc) of VO2(M), temperature-transmittance reversible hysteresis loops were measured at a fixed wavelength of 2000 nm, as shown in Figs. 4(a)–4(c). The heating and cooling paths are labeled as Heating and Cooling, respectively. Figures 4(d)–4(f) display the first derivatives of the thermal hysteresis loops for the S1, S2, and S3 films. After incorporating Ag, the amplitude of the hysteresis loop is notably reduced, which is attributed to the strong absorption from surface plasmon resonance of the Ag particles in the visible to near-infrared region.[12,37,38] To accurately determine Tc, the Gaussian method was applied to obtain Tc-H and Tc-C during heating and cooling, respectively. Here, the critical temperature for the semiconductor-to-metal transition is defined as the midpoint of the thermal hysteresis loop

    According to Eq. (4), the Tc for S1, S2, and S3 are calculated to be 67.4 °C, 55.2 °C, and 52.2 °C, respectively.

    The significant reduction in Tc after introducing Ag can be explained by the theory proposed by Zylbersztejn and Mott.[12,34,39] Since the work functions of Ag and n-type VO2(M) are 4.63 eV and 5.4 eV, respectively, the contact between Ag and the VO2(M) film forms an Ohmic junction (Fig. 4(g)). In this case, free electrons flow from Ag to VO2(M) until the Fermi levels (EFm and EFs) align. These injected electrons absorb additional energy (WA) at the metal-semiconductor interface, thereby facilitating the phase transition at a lower temperature.[12,34,39] The Tc of S3 is lower than that of S2 because the shell/core protruding Ag structure in S3 provides a much larger contact area with VO2(M) than the flat film-like Ag in S2 (Fig. 4(h)). Considering that the effective electron injection depth from Ag into the VO2(M) film is only several tens of nanometers,[12] increasing the contact area effectively increases the number of injected electrons. Hall measurements at room temperature (Fig. 4(i), red dashed line) reveal carrier concentrations of 2.67 × 1018 cm−3, 33.23 × 1018 cm−3, and 51.38 × 1018 cm−3 for S1, S2, and S3, respectively. This further confirms that, with the same Ag content, the VO2(M)–Ag composite in S3 embedded within the SiO2 array substantially increases the Ag/VO2(M) contact area, enabling more efficient electron injection from Ag to VO2(M) and consequently further reducing Tc.

    Figure 5(a) shows the transmittance spectra of all samples within the 350–2500 nm range at 25 °C and 90 °C. Due to the strong inherent absorption of VO2(M) in the short-wave region, the samples exhibit higher transmittance in the near-infrared range compared to the visible range.[13] All samples show high dynamic modulation capabilities in the near-infrared, with a marked transmittance contrast in this region between the two temperature states. At low temperatures, the films are relatively transparent to near-infrared light; while at high temperatures, they effectively block near-infrared transmission.[13] The behavior further confirms the presence of VO2(M) within the films. Notably, at low temperatures, the transmittance of S1 is significantly higher than that of the composite films, which can be attributed to the unique localized surface plasmon resonance properties of noble metal nanoparticles that strongly absorb light in the visible to near-infrared range.[12,37] As shown in Fig. 5(b), the absorption spectra of the composite materials S2 and S3 at room temperature and high temperature are significantly higher than that of S1. Compared to composite film S2, the room-temperature transmittance spectrum of S3 exhibits a distinct dip around 600 nm. The effect is attributed to the two-dimensional diffraction grating properties of the VO2(M)–Ag–SiO2 shell/core monolayer structure, which strongly scatters light at specific wavelengths, thereby reducing transmittance.[24–27] Additionally, the structure exhibits unique structural coloration, allowing for color modulation.

    The optical parameters of all samples were calculated based on Eqs. (1)–(3), and the results are summarized in Table 1. The Tsol of S1 at 25 °C is 53.2%, and the ΔTsol is 18.9%, which is consistent with the results reported by Hao et al.[39] For the composite materials, after embedding the SiO2 nanosphere array, the ΔTsol increases from 22.8% (S2) to 25.4% (S3), while the ΔTlum increases by nearly 7 times (from 0.6% (S2) to 4.3% (S3)). By embedding SiO2 arrays into VO2(M)–Ag composite films to form a shell/core monolayer structure, the optical performance of the films in the visible light region is effectively tuned, achieving color modulation while significantly improving solar energy modulation efficiency.

4.   Conclusion
  • By the electron-beam evaporation method, a monolayer hexagonal close-packed SiO2 array was successfully embedded into VO2(M)–Ag composite film, forming a VO2(M)–AgSiO2 shell/core photonic crystal structure. Compared to the flat VO2(M)–Ag composite film, the shell/core structure of the VO2(M)–AgSiO2 composite film increases the contact area between VO2(M) and Ag, which facilitates the injection of more free electrons from Ag into VO2(M), thereby further lowering the phase transition temperature to 52.2 °C. By embedding the SiO2 array, the solar modulation efficiency of the film increases to 25.4%, and the visible light modulation efficiency rises by nearly an order of magnitude. Additionally, the film exhibits a grating effect, strongly diffracting light around 600 nm, which weakens the strong absorption of VO2(M) in the short wavelength range due to electronic transitions, thus altering its inherent brownish-yellow color. These results provide valuable insights for the study of VO2 films in smart windows, and further improvement of the film properties holds promise for commercial applications.

Figure (5)  Table (1) Reference (39)

Catalog

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return